[Wien] jhw probleme /joe-firmware openvpn

[Felix Ehritz]

so hab jetzt die tunnel config laut joe gemacht!
sieht so aus:

login as: root
(spam-protected)'s password:


BusyBox v1.15.3 (2011-05-28 23:14:05 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  |_______||   __|_____|__|__||________||__|  |____|
           |__| W I R E L E S S   F R E E D O M

OxFF-Funkfeuer Freenet  ---------------------------
   * OpenWRT (backfire, r27025)
   * LuCI  (trunk, r7109)
   * 0xFF-Snapshot r1065 by JoeSem
   -------------------------------  Vienna, 2011-05-28
(spam-protected):~# cd ..
(spam-protected):/# cd etc
(spam-protected):/etc# cd config
(spam-protected):/etc/config# vi openvpn
config 'openvpn' 'to_krypta'
option 'dev' 'tun'
option 'management' '127.0.0.1 31194'
option 'nobind' '1'
option 'verb' '3'
option 'remote' '78.41.115.228'
option 'proto' 'udp'
option 'dev_type' 'tap'
option 'comp_lzo' '0'
option 'enable' '1'
option 'ifconfig' '78.41.112.81 255.255.255.000'
option 'port' '5031'


was fehlt? im webinteface steht tunnel gestartet, aber als nachbar find 
ich den tunnel nicht!

ifconfig sagt:

(spam-protected):~# ifconfig
br-lan    Link encap:Ethernet  HWaddr 00:15:6D:C1:B7:FF
           inet addr:78.41.112.81  Bcast:78.41.112.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:652 errors:0 dropped:0 overruns:0 frame:0
           TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:474497 (463.3 KiB)  TX bytes:4264 (4.1 KiB)

eth0      Link encap:Ethernet  HWaddr 00:15:6D:C1:B7:FE
           inet addr:10.0.0.15  Bcast:10.0.0.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:476 errors:0 dropped:0 overruns:0 frame:0
           TX packets:91 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:127913 (124.9 KiB)  TX bytes:37373 (36.4 KiB)
           Interrupt:4

eth1      Link encap:Ethernet  HWaddr 00:15:6D:C1:B7:FF
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:656 errors:0 dropped:0 overruns:0 frame:0
           TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:488657 (477.2 KiB)  TX bytes:4264 (4.1 KiB)
           Interrupt:5

lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:24 errors:0 dropped:0 overruns:0 frame:0
           TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:1600 (1.5 KiB)  TX bytes:1600 (1.5 KiB)

tap0      Link encap:Ethernet  HWaddr 56:5F:13:AF:56:F1
           inet addr:78.41.112.81  Bcast:78.41.112.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:100
           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

zusammen gefasst:
eth0 ist mein wan (router privat=internet)
eth1 ist mein lan (an dem hängt dann die andere ff-hardware)

eth 0 spricht kein olsr (da ja am priv. router)
eth 1 spricht olsr